hydraulic pump manufacturers kawasaki hydraulic pump

After the required pressure of the hydraulic oil tank, after each time you start the machine, you have to wait to use the pressure of hydraulic stains box before they can start operating machinery. Once the hydraulic reservoir pressure is insufficient, served as the machine will pump and slip inside the whip phenomenon caused by the pull-off, then the cause is not normal wear and tear the body board and return the pump platen. After using the charge pump supply piston pump 3000h, operators need to check piston 1-2 times a day to check the pump operation is not a normal sound. If the cylinder speed drops or stuffy car situation, you should check the disintegration of the charge pump, check the impeller edge if there are scratches phenomenon, the internal gear pump gap is too big.

For self-suction-type piston pump, the hydraulic oil tank must not fall below the lower limit of the oil standard, to maintain a sufficient amount of hydraulic oil. Cleanliness of hydraulic oil higher, longer pump life.

View high-pressure pump job before the job is as follows:

Before 1 primary electric pump equipment using first check the voltage status, and plugs, sockets to see is not connected;

2, one end of the high-pressure pipeline, links on the electric pump device connector, the other end connected to the needs of the things;

3, pay attention to both ends of the connector before use is not locked into place, it is necessary to move to the top of what the joint force, without relaxing the conditions screwed jacket nut. If not locked in place there will be the appearance of oil can not pass, and then will attack without the operation of the machine status.

Before use it is necessary to view the ministries is not normal. Use should be in strict compliance with the rules of the main parameters, avoid ultra-overload, or when lifting height or lifting tonnage in excess of the rules, electro-hydraulic jack unit will attack a serious oil spill. Please refer to the electric pump electric pump to use instructions. Weight center of gravity to choose moderate, reasonable selection of electro-hydraulic jack focal point, to pad the bottom level, taking into account conditions on the ground soft and hard, is not to the timber liner tough, place is not stable to avoid load subsidence or skew.

Electric pump in the use of open air should turn the nut, turn the switch on the set of oil blocks, plug in the power, and set in the joint rapid equipped with hydraulic equipment rapid head. Press the power switch, rolling 1-2 minutes until the motor will switch into a closed pressurized state, the output will be the job of hydraulic oil, hydraulic oil output increases with the load and self-boost the work carried out until 63MPA .

On the diaphragm and piston Performance Comparison

????Now only the electric plug and electric airless sprayer airless sprayer estrangement compare the DC motor piston is movable piston reciprocating shares will paint inhalation, pressurized discharge, because it exposed the plunger and column Cypriot coated guess work at paint grinding effect plunger wear very quickly, once with a larger diameter nozzle plungers reciprocating frequency progress, increased plunger wear, machine life expectancy is short. And replace the plunger offer very expensive, if the voltage is not normal operation will directly cause direct current is not normal. In addition, because a significant back and forth movement of piston pump pulsation great job, so spray instability, wall roughness on spray paint is not good enough. But initial suction piston faster its interests. Estrangement airless sprayer (estrangement pump), the planning is on the piston foundation has been greatly improved, the principle of the femoral artery reciprocating motor operation (note, the piston is not in direct contact with paint), and then promote the estrangement campaign, will paint absorption pressure introduced through the nozzle sprayed coating object, because its anti-wear piston oil operations, greatly improving the working environment, life expectancy greatly improved by doping piston through hardening process is even more difficult to damage plus high resistance barrier polymer material twisted more so pump life expectancy gap further progress. Reliable pump operation is another benefit gap, the failure rate very end of the voltage request bottom, bottom to the environment request, repair simple, fifth at the mercy of the repair costs only piston pump. Estrangement pump excellent value for money, which offer excellent performance ratio will advance estrangement pump promotion. Kan Bell Airless sprayer with a number of the world's leading pioneering skills. Prime Booster TM system can use to restart in seconds and loading, handling the airless sprayer initial suction tough skill challenges, innovation of DAP IV inlet valve plan greatly reduces the valve is stuck maybe paint, plus High-power electric motor and the consolidation of a molding shell, Kan Bell sprayer can serve a variety of short duration high industry job assignments administered. Another element of the nozzle is seriously affecting the quality of the coating. Its quality was evaluated as